下載 App
關注我們
  • Facebook
  • YouTube
  • Instagram
  • TikTok
  • X

Malaysia First Reports Rear Wheel Detachment, Domestic Recall Follows: What's Wrong with Chery's Rear Axle?

2026-11-16 16:40:00
Penguin
0 Fans   224 Following   9 Posts


Evening of November 6, the State Administration for Market Regulation posted a recall announcement: Chery will recall some Tiggo 5X and OMODA produced between June 6, 2022 and December 31, 2023, starting November 27, totaling 53,882 vehicles. The defect description is potential poor welding between the rear axle longitudinal arm and the sleeve; in extreme cases, the weld seam may fail and separate, causing wheel loss of control. A month ago, an OMODA 5 in Malaysia suffered rear axle tearing while driving normally, with two rear wheels along with the rear axle assembly detaching from the car body; the video spread across the internet. This domestic announcement is the follow-up to that incident. The same rear axle, the same welding defect, from Southeast Asia to the domestic market, Chery completed the process in less than a month, but the problem itself may be deeper than the announcement states.

Malaysia First Reports: Two Rear Wheels and Axle Detached Together

On October 6, Johor Bahru, Malaysia, a 2023 model OMODA 5 had its rear axle longitudinal arm weld seam tear while driving normally, and the two rear wheels along with the rear axle assembly detached directly from the car body. No casualty records were found in public reports, the only luck in this incident. On October 11, Malaysia Land Transport Authority made a decision: suspend OMODA 5 model certification, suspend new vehicle registration, until the technical investigation ends. That night, Chery released a statement on Weibo, admitting insufficient welding strength at local welding positions for the rear axle longitudinal arm of this batch of vehicles, and there exists a risk of weld seam tearing in extreme conditions, while also stating that this structural model has previously been discontinued. Chery Malaysia subsidiary initiated recall for 8,878 OMODA 5s to inspect and replace parts for free as needed. The same statement also mentioned that special risk screening for same-batch models in domestic and related markets has been initiated.

Domestic Follow-up: 53,882 Units, Starting November 27

Domestic recall scope is six times larger than Malaysia's. 53,882 units, production interval from June 6, 2022 to December 31, 2023, about 19 months. Disposal method in two steps: first visit store for free inspection of rear axle production date code, only replace rear axle if belonging to defective batch. 53,882 is the screening scope, actually only a part might need replacement. Chery customer service phone 400-883-8888, car owners can also log in to State Administration for Market Regulation Recall Center website to self-check using 17-character VIN code. If you bought Tiggo 5X or OMODA within this production interval, and normally driving rear wheels shake or chassis makes abnormal noise, do not take the highway, go to dealership first to check and eliminate hazards. Chery will notify relevant owners via SMS and registered mail, but proactive check is more secure.

Twice in Two Years: From 3,037 to 53,882 Units

This rear axle problem happened before. On June 21, 2024, Chery recalled 3,037 Tiggo 5Xs due to rear axle longitudinal arm and sleeve welding problems, production interval from August 22, 2023 to October 30, 2023, two months and a few days. The reason in that announcement was written specifically: "Welding equipment reason". This announcement for 53,882 units, the reason changed to "Manufacturing process problems", phrasing became vague. Production interval expanded from about two months to about 19 months, indicating the scope in 2024 was too small, vehicles produced over 16 months were not included at that time, now added. Same component, same failure mode, same disposal method, two recall rounds in two years, number flipped from 3,037 to 53,882, nearly 18 times.

Root Cause Inquiry: From Welding Equipment to Manufacturing Process

The 2024 announcement pointed the root cause to welding equipment, if it is a calibration deviation of a welding machine, defining the scope by equipment usage time window is reasonable. Two years later, problem occurred in same location again, reason description became vague instead—is it unclear, or known but hard to say? If 2024 repair was just surface level, then welding defect on this rear axle might involve multiple machines, multiple shifts. Chery has not publicly answered this question to date. What should be questioned more is: In these two-plus years from June 2024 to November 2026, the over 16 months production of cars equipped with same rear axle, do owners know their cars might have hazards? Whether recall scope is accurate directly decides how many people are driving on the road with problems. Announcement also did not disclose how poor welding was discovered, how many failures occurred, this information absence makes 53,882 number read heavier.

Going Global and Quality Control: Yin Tongyue Says "Going Global Is Not Harvesting"

On October 21, Chery Chairman Yin Tongyue at World Intelligent Connected Vehicle Conference, publicly apologized to Deputy Minister of Malaysia's Ministry of Industry, said a sentence later quoted repeatedly: "Going global is not harvesting, must be humble and low-key, cannot boast wildly, blind expansion is easy to turn into wasting resources like filling the sea." This sentence was well said, 16 days later quoted again by Chery's own recall announcement. Chery Q1-Q3 exports 1.4991 million vehicles, YoY growth 66.3%, export proportion close to 70%. OMODA volume in domestic is limited, overseas acted as main force, its quality problems first exposed overseas, domestic follows screening and recall, this sequence deserves thought. Huxiu said in mid-October comment "Attitude is attitude, Craftsmanship is craftsmanship", this sentence is the key point of this event. Recall is remedial measure, if quality control bottom line is loose, how many recalls can't make up for it.

Summary: 53,882 units is just screening start point. Announcement did not disclose how poor welding was discovered, how many failures occurred, proportion of 53,882 units actually needing rear axle replacement. These numbers are key to separate recall scope and real defect batches. For owners, production date stuck between June 2022 to December 2023, go check VIN and rear axle code ASAP. For Chery, going global to push volume is fine, chassis welding basic process shouldn't have low-level errors, and shouldn't happen twice.

意見反饋